 |
For sale & wanted
Date: 02nd September 10
Headline: Wanted 40mm Lectron Carbs
User: Nick Saunders
Wanted
A set of 40 mm Lectron Carbs, please see attached email address or fill in form at www.afbdragracing.co.uk
Date: 30th August 10
Headline: Wiesman 4 speed--Kaw parts
User: Bryan Bennett
Very nice Wiesman 4 speed for a KZ or can be used in J cases with the correct output bearing--cant tell its been ran---only about 12 1/8th mile passes on it---it scared the guy too much and he parked the bike---now parting it out.I am listing these parts for him and handling all the transactions.Trans is complete --with shifter,16 tooth fine spline 3 inch offset 630 sprocket with beraing nose.Comes with a shifter hat that has the Kosman 6 bolt pattern to fit the shifter to the outboard bearing retainer --also comes with 6 brand new extra gears.Over 7000.00 of trans stuff new ---plus its seems just about impossible to actually get one.3500.00 USD
Pro mod style NOS system--complete--4 individual plates,nozzles,flare jets 24-28-32-34,braided lines,shower heads,cheater solenoids,purge,holley red pump,bypass regulator,pressure gauge,a switched throttle housing for lectrons,four 2lb bottles and one 2 1/2 lb bottle--650.00 with 1 bottle---900.00 with all 5 bottles
Schnitz Top Gas box with Dyna 2 ohm blue coils with dyna wires,blue dyna pickup and billet rotor-like new--money back guarantee not DOA--600.00
GPZ crank,falicon knife rods,18mm wrist pins--16 tooth center pin--Funny Bike prepped(pinned)--like new--bought brand new crank from Kawasaki and had it done up by HMP--2700.00 invested---will take 1000.00
Nice 1979 MKII engine cases(black)----with APE studs for MTC head,lowercase studs,main cap plate and my design crank support system,my design mods to oil pan,pump and filter housing for rear oil pickup,bored to 3.490-----these cases have never had anything broken in them.Clearanced for the wiesman KZ4 trans but any trans will still work in them.NO stripped threads------350.00
KZ Big block---82mm bore(1395)--was a spare---never been ran since resleeve,new bore,decked and o-ringed-can be bored again to 83mm(1425)--ready to use---450.00
84 GPZ head---stock---still all together--ie--valves,springs,shim on bottom buckets,keepers,spring seats-----350.00
MTC slider clutch--like new-- twelve 1/8th mile runs--complete except for--no clutch plates-----600.00
If you find anything not as described--or not to your liking--your money will be refunded (minus shipping)when parts are returned unused--except for the electronics--you have to hook them up to see if they work and they are only guaranteed not to be DOA.
I can be reached at Bennett662@mchsi.com or call 618-925-6529
Date: 27th August 10
Headline: HD CLASSIC SHOVEL TOP-GAS BIKE 115cui.
User: BUSTER
HD CLASSIC SHOVEL TOP-GAS BIKE 115cui.The bike is set up for going on 116-120 Oct race fuel.Before total rebuild the ET was ¼ mile 9, 49 sec 229km/h. The potential of this bike is to drive stabile and going in top five for ET pro class.It has gone thru total rebuilding in the winter 2008-09 with help from Ronny Aasen.
REBUILD EDLUN FRAME. FRONT END KAWASAKI.
DELKRON BIG BORE CASES ZEKE CYLINDERS 3 13/16".
S&S 5" STROKE. CARILLO FORGED H-RODS.
JIMS CRANKPIN & BEARINGS. S&S BREATHER VALVE.
ANDREWS RACE CAM. JE FORGED PISTONS.
CUSTOM SHOVEL HEADS BY "PUMPEN". KIBBELWHITE VALVES.
AMPCO 45 GUIDES. PROSPRINGS +700"
NEW ROCKER AXELS. S&S ROLLER ROCKERS.
JIMS BIG AXLE LIFTERS. JIMS CRMO ADJUSTERS.
CRMO BASE & HEAD HARDWARE. MIKUNI HSR 48 SMOOTHBORE.
HIGH PRESSURE NEEDLE-VALVE. HUCO ELECTRIC FUEL PUMP.
4" AIR INTAKE. BIG CUSTOM PLENUM MANIFOLD.
CUSTOM 2:1 RACE EXHAUST. DYNA 4000 SUPER PRO IGN.
DYNA SHIFTLIGHT & KILLSWITCH M.R.E AIRSHIFT.
NEW 10"x 16" SLICKS. 4 IN 5 S&S TRANSMISSION CASES.
BILLETT DOOR. BILLETT PILLOW BLOCKS.
BILLETT FORK ROD. ANDREWS GEAR 2,94 LOW.
BILLETT SHIFT DOWN. GEARS ARE PRO CUT STRESS RELIEVED + ANNEALED TRANS.
HAS (ANTI) OVERSHIFT MOD DONE TO CHANGE ARM + DRUM.
RIVIERA PRO CLUTCH.
OFFERS AROUND 12,000 EUROS HAGGLE WITH BUSTER
atle.jor@online.no PHONE - NORWAY 48035855
PHOTOS ON
http://www.turboville.co.uk/turbo-7/classifieds.htm
Date: 20th August 10
Headline: Brand new Hayabusa for 9.50 bike
User: Stephen
For sale, brand new 2009 Hayabusa suitable for 9.50 bike or similar. Best of everything fitted.
Standard motor with various Walter Sprout tweaks (PAIR valve, short stacks, water pump, countershaft, etc)
Boostbysmith software, mapped and dynoed by Walter Sprout, 195bhp
Murray step sidewinder pipe
MPS oil pan and DME windage tray
Scott billet oil filter with Exoticycle filter relocator
Hays clutch
RaceMachine billet sprocket cover
MTC billet clutch cover
10" over Velocity swing arm, 68" wheelbase
JRi shock
Custom fitted Tiger Tail
Colour matched 8" over Catalyst seat
Brock lowering links
Michelin Power One front and rear
Chain and gearing upgraded (16/45)
Ceramic wheel bearings
Oberon footpegs
MPS shifter with Spencer Cycle bracket
Scott steering damper
Spencer Cycle top yoke, strapped front end
Catalyst low profile front mudguard
Pazzo levers
MSD programmable shiftlight
The bike and all parts are new, the only usage is the dyno pulls.
As you can see, all the best parts. Need to shift it, make me a sensible offer.
Date: 12th August 10
Headline: Shorrock blower
User: Keith Porter
C.75b with mounting plate/twin v belt pulley from typical 70s drag bike.offers. Keith.tel.0208 397 1783.
next page
Your For sale & entry
You can submit your own for sale entry here. Please take care that your email adress is valid and that you post an
image in order to amplify your sale entry. The image should not be larger than 100KB and not wider than 560 Pixels.
We will check your entry and set them free in time.
|
|
|
|
